Field glossary · measurement
GPH / GPM
GPH, gallons per hour, and GPM, gallons per minute, express flow over different time intervals: a 120 U.S. GPH outlet equals 2 U.S. GPM, or about 7.57 liters per minute. The conversion uses 60 minutes per hour while retaining the gallon convention. Keep the converted flow separate from watering duration, and compare it with both the minimum and maximum flow of the control valve. A small zone can be below the valve's operating range.
Gallons per hour, the emitter and drip flow unit; gallons per minute, the spray unit. GPH divided by 60 is GPM
Keep the gallon definition with the flow rate
NIST Special Publication 811, 2008 edition, lists approximately 3.785412 liters per U.S. gallon and 4.54609 liters per Imperial gallon. A catalog using Imperial GPH therefore describes about 20.1 percent more water than the same numerical U.S. GPH rating. The hour-to-minute conversion does not resolve a gallon mismatch.
Using NIST's U.S. gallon factor, a 120 GPH pump rating converts to 2 GPM and about 7.57 liters per minute; reversing the time conversion gives GPH = GPM x 60. Put the gallon convention beside the duty point on a water-feature pump schedule so imported and domestic ratings can be compared at the same head.
Measure an emitter with a timed catch
Flow equals collected volume divided by collection time. With volume in milliliters and time in minutes, U.S. GPH = mL x 60 / (3,785.412 x minutes). Catch the complete discharge in a graduated container and retain the elapsed time with the reading. Use the steady operating condition, rather than the short fill or drain-down period.
An emitter delivering 300 mL in 5 minutes measures about 0.95 U.S. GPH. NIST's conversion factor puts a 1 U.S. GPH emitter at approximately 315 mL in that interval, so the catch is about 5 percent below the rating. Compare the result with the specified product's flow-versus-pressure data at the measured inlet pressure.
Why a small drip zone still needs a flow-range check
Rain Bird rates its XCZ-075-PRF low-flow control-zone kit for 0.2 to 5.0 GPM. The lower limit equals 12 GPH. Eight 1 GPH emitters total only 0.133 GPM, below that kit's published range. Twenty such emitters total 0.333 GPM, inside the flow range. Reducing the watering duration changes delivered volume, not the flow while the valve is open.
Read the inlet-pressure requirement at the selected flow as well. Rain Bird's performance chart requires 43.4 psi inlet pressure for the XCZ-075-PRF to provide a 30 psi outlet at 5 GPM. At 0.2 GPM, the listed minimum inlet pressure for that same outlet is 34.4 psi. A regulator's outlet label does not mean an equal inlet pressure will sustain it under flow.
On the drip-zone schedule, add columns for connected GPH, converted GPM, valve minimum, and required inlet pressure. The eight-emitter zone fails the minimum-flow comparison before supply capacity or runtime enters the decision.
Distinctions
- Gallons delivered
- At 20 GPH, a 15-minute cycle applies 5 gallons. A meter total of 5 gallons without elapsed time cannot tell whether the zone ran at 20 GPH or another flow rate.
- Pressure
- Pressure describes the hydraulic condition driving flow. A pressure reading alone does not measure the discharge reaching an emitter or fountain outlet.
Frequently asked questions
Can a valve be too large for a drip zone?
Its operating range can begin above the zone demand. Select by the published minimum and maximum flow, rather than assuming that any valve with enough upper capacity will work at the low end.
Why does my measured GPH differ from the label?
Retain the gallon convention, catch duration, and inlet pressure with each reading. Comparing those records across the irrigation audit locations separates a consistently low zone from an isolated low-output emitter.
Sources checked
Also defined as
- Gallons per hour or per minute of pump flow; 60 GPH equals 1 GPM