ANVILFIELD Try FieldOS

Field glossary · measurement

pH

pH is the negative base-10 logarithm of hydrogen-ion activity. USGS explains that each pH unit represents a tenfold activity change, so pH 6 water has 100 times the hydrogen-ion activity of pH 8 water. The reading has no units and does not measure neutralizer demand. Report the sample temperature, material, and preparation method: a soil extract, wetted concrete surface, and condensate stream represent different measurements on the same scale.

Surface acidity or alkalinity, tested separately against the selected adhesive’s published range

Used across 4 Anvilfield field guides, most in Concrete.
Updated

One pH unit is a tenfold chemical change

USGS's 2021 Measurement of pH chapter states that a change of one pH unit represents a tenfold change in hydrogen-ion activity. Moving from pH 6.0 to pH 8.0 therefore reduces that activity by a factor of 100. The logarithmic relationship does not tell an operator how much neutralizing chemical the water will consume.

USGS gives neutral pure-water pH as 7.00 at 25°C and 6.92 at 30°C. The same chapter reports pH 5.7 for pure water equilibrated with atmospheric carbon dioxide at 25°C. An exposed water sample can change chemically as gas dissolves; a later reading in an open cup need not reproduce the original stream measurement. Record temperature and sampling time rather than treating every change as meter drift.

Calibration must test more than the display

EPA Method 150.3, version 1.0 (February 2017), requires user-calibrated bench-top and portable drinking-water meters to use at least two buffers bracketing the expected sample pH and approximately three pH units or more apart. It then requires another reference buffer for verification, with a result within ±0.1 pH unit of its true value. A two-decimal display does not demonstrate that performance.

EPA Method 150.3 sets at least weekly calibration and daily buffer verification, or at measurement when monitoring is less frequent; a failed daily check triggers recalibration. A buffer with a temperature-correct reference value of 7.00 that reads 7.18 fails the ±0.1 verification limit. Keep the reference value and observed result together. These are drinking-water method criteria, rather than a calibration schedule imposed on soil, flooring, or condensate work.

Concrete surface pH measures the wetted test spot

ASTM F3441-24a describes the comparative change in reagent-water pH on a properly prepared concrete surface, at that location and time. Its result is not a measurement of the entire slab's pore solution. Surface preparation and the water used are part of the measurement, so results from different preparations should not be merged into one unexplained trend.

ASTM F710-26 addresses concrete-floor preparation for resilient flooring, while F3441-24a describes the comparative pH measurement. Keep the adhesive or floor-system product name and its published limit beside each local result in the slab testing record. A passing reading at one prepared spot does not describe a different surface treatment or the whole slab's internal solution.

Distinctions

Alkalinity
pH describes hydrogen-ion activity; alkalinity describes acid-neutralizing capacity. Two waters with the same pH can consume different amounts of treatment chemical.
Electrical conductivity
Conductivity responds to dissolved ionic species collectively. It does not identify hydrogen-ion activity and cannot replace a calibrated pH measurement.

Frequently asked questions

Can I average inlet and outlet pH to size a neutralizer?

An arithmetic average of pH readings does not establish a chemical dose. The special-waste guide covers treatment systems; keep the stream flow and neutralization demand separate from the measured pH.

Why do soil and condensate readings need different records?

A soil result includes the extraction or preparation used by the laboratory, while condensate represents a liquid stream at a sampling point. See soil testing and neutralizer outlet testing for those applications.

Sources checked

Also defined as

  • Plumbing: Measure of acidity, 7 neutral, lower is acid, higher is caustic; discharge is held to a set range
  • Landscaping: Soil acidity or alkalinity; most turf wants about 6.0 to 7.0, which keeps nutrients available

Where this shows up

Next step: Find commercial grounds accounts

Back to the full field glossary